Skip to content

Backyard Patio Transformation

February 19, 2016

Skip gallery slides

With not much more than a concrete slab and a patch of grass to go on, this homeowner transformed his backyard into a stylish outdoor retreat. See how he did it, and get great cost-cutting ideas for your own yard remodel project!

Start Slideshow

1 of 22

Beautiful Backyard

The homeowner and designer knew his backyard had potential. And he had a plan. The tiny patch of grass behind his 1950s split-level would be plain no longer! With ready-made materials and his own blueprint, the homeowner created an outdoor retreat for his friends and family.

Advertisement

Advertisement

2 of 22

Patio Landscaping Tips

Learn how to landscape the area around your patio like a pro with these quick and easy ideas.

3 of 22

Cold Concrete

Before the makeover, the back patio was small and cluttered. The unwelcoming concrete slab didn't scream impromptu BBQs or intimate dinner parties with friends. There was barely enough room for two backyard basics: a picnic table and grill.

Advertisement

4 of 22

Slippery Slope

The small backyard provided great green space. However, it sloped steeply into the bramble and bush of a wooded ravine.

5 of 22

Breaking Boundaries

With a plan in mind, the first step was to extend the existing concrete patio. First, a level surface was created on the sloping ground. A retaining wall also helped solve this problem.

DIY Tip: Use what you have. Extending this small patio solved a big space problem. Adding on to existing elements will save time and money that you would sacrifice in a major overhaul.

6 of 22

Water-Ready

Flexible plastic tubing was placed along the length of his retaining wall to drain water away from the block wall.

Advertisement

Advertisement

Advertisement

7 of 22

Excavate Your Space

Inside a clearly defined perimeter, about 6 inches of dirt was removed by hand, making space to lay the new patio surface.

8 of 22

Shovel It In

Once the work was done digging out space for the new patio, it was time to start filling it in. Three inches of crushed limestone was applied, then topped it with 1 inch of paver base (or sand).

9 of 22

Down Flat

For any new patio project, it's easy to create a flat surface by compressing gravel with a rented tamper. Running a 2x4 over the surface when you're done creates a smooth finish.

Advertisement

Advertisement

Advertisement

10 of 22

Lay The Groundwork

Concrete pavers were used to create a visually interesting and flat patio surface. Stakes and 2x4 spacers helped organize the blocks perfectly while they were laid. As a finishing touch, river rock was poured into the cracks between the blocks -- just like grout in bathroom or kitchen tile jobs.

DIY Tip: For tricky blocks that must be cut to a specific size, contact a local stone dealer to slice them for you.

11 of 22

Personalize It

The once cold and cramped space is now a 14x16-foot patio with room for a table for 10. But no space is complete without some personal touches.

DIY Tip: Change things up to make your space more interesting. Using wood, concrete, and plastic materials includes contrasting textures that give the patio space depth. The almost neon pops of color from the chairs stand out against the yard's natural shades.

12 of 22

Fun and Functional

Make food service functional. Eliminate constant trips inside during a party by creating a buffet area outside. An old potting bench was used to create an outdoor buffet for this patio space

Advertisement

Advertisement

Advertisement

13 of 22

Surface Needs

Just like indoor spaces, outdoor entertaining areas benefit from lots of places to set drinks and food. The homeowner made these chic side tables himself. Here's how he did it:

Step 1: Choose a 24-inch tall piece of terra-cotta chimney flue based on the size of tabletop you're planning. The flue used on this table is 18 inches in diameter. Position the flue on your patio and reinforce the surface as needed.

Step 2: Place a square panel of lattice or fencing atop the flue. For some really great designs, visit latticestix.com.

Step 3: Top the table with a 1/4- to 1/2-inch-thick glass slab. A glass or mirror fabricator can cut this final piece to size and add a beveled edge or other treatment.

14 of 22

Stone Solid

The homeowner/designer searched a variety of sources for his stone products, including misfired concrete slabs, which he used as accent pavers, and these retaining wall blocks. They combine to create lots of seating areas and a perfect place to set plants and other garden accents.

15 of 22

Backyard Basic

What's a meal outdoors without a picnic table? This DIY project is a spin on a classic backyard essential. Here's how the homeowner/designer brought it together.

Step 1: Cut cedar 2x4 boards and 4x4 posts to the desired length. Lay the boards on a level surface, placing 1/4-inch spacers between the boards, until you reach the desired width.

Step 2: Cut several 2x4s approximately 1 inch shorter than the width of the tabletop. Place these 2x4 braces evenly along the length of the table (here, five were used). Use decking screws to hold the 2x4s in place on the bottom of the tabletop. Remove the spacers and set the top on a base.

Advertisement

Advertisement

Advertisement

16 of 22

Design a Container Garden

Learn how to create an eye-catching container garden with these expert design tips.

17 of 22

Great Legs

Chimney flues form the legs of this modern picnic table. To find some like it, visit a masonry supply store. Be sure to ask for hard-fired terra-cotta. To achieve the right height for comfortable seating, you may want to set a 4-6-inch stone block under each flue. Flue pipes typically come in 24-inch-long segments.

18 of 22

Planter Plumbing

Usually, the only colorful things popping out of sewers are bright orange hard hats. Here, the homeowner/designer planted gorgeous greenery inside stacked, precast concrete manholes.

Advertisement

Advertisement

Advertisement

19 of 22

Cover Up

Talk about making the most of what you have. Before the makeover, this area once featured a wood post and gutter -- in other words, an eyesore. With the help of bricks held together by masonry adhesive, it's now an architectural column.

20 of 22

Take a Cue

Pool balls were used to add a punch of color to green potted plants. Find other unusual items at flea markets, yard sales, and secondhand stores to bring character to your own outdoor spaces. As these planters prove, your accents don't have to be huge to make a fun impact. (But you may want them to be weatherproof!)

21 of 22

Privacy Panel

To get privacy without resorting to a heavy, light-blocking wall, the homeowner/designer created these wood panels to separate his yard from the neighbors'. Here's how to make them yourself:

Step 1: Plan your panel arrangement. You'll need to dig holes approximately 42 inches deep every 8 feet or so. Consider renting a power auger for speedier digging.

Step 2: Position cedar posts in the holes. Backfill with gravel and then soil. Use a level to ensure posts are perpendicular as you backfill.

Step 3: Starting at the top, attach 1x4 cedar boards with deck screws. Keep things perfectly horizontal by checking your progress frequently with a level.

Advertisement

Advertisement

Advertisement

22 of 22

Walk This Way

Instead of a gate, the homeowner/designer set one wood-slat panel back a few feet to create an easy walkway. Without sacrificing its sleek, contemporary style, the fence remains functional and welcomes guests into the new backyard retreat.

Up Next