No-Sew DIY Curtains and Shades
Dish Towel Curtains
Lengthen too-short curtain panels with this super easy no-sew technique.
Napkin Cafe Curtains
Turn patterned cloth napkins into a kicky pair of curtains by joining their edges with jeans rivets spaced every 2 inches. Then add large grommets or rivets along the tops of the panels and thread onto a curtain rod. You can buy rivet and grommet kits at fabric stores. To install, cut a small hole in the fabric, insert both pieces of the rivet or grommet, and use the tool that comes in the kit to press them together.
Romance a window with a pretty curtain made from a tablecloth. Look for a square or rectangular one with tassels, ruffles, or scallops -- they'll add instant detail that you don't have to sew on. Cut the tablecloth into two panels. (A 60-inch square cloth is handy because you can just cut it in half.) Hem the cut edges with iron-on seam tape, and hang with drapery clips.
Update plain curtains with painted stripes with a specialty paint. Watch to reveal what kind of paint you need, plus the secrets to striping success!
Towel Window Treatment
Use kicky kitchen dish towels for fun window treatments. Simply clip drapery hooks to the top edge of a dish towel and hang from a cafe curtain rod. The towels are easy to remove for washing and can also be changed out seasonally. Plus, when you've decided to move on to a different window treatment, the towels can be used for their original purpose of drying dishes.
First, cut two panels of sheer fabric to fit your window. Hem the edges with no-sew adhesive strips. In a bucket, mix fabric dye with water until the desired saturation is achieved, then dunk the doilies in the dye. Remove from the dye and let dry. Adhere the doilies to the curtain panels with a hot-glue gun. Arrange the doilies in a random pattern, and for a cropped look, adhere a few doilies along the edge and trim accordingly. To finish the curtains, glue a lace remnant to the bottom of the curtain, leaving an inch or so extra on either side to fold over and finish the edges.
The buttons and burlap that jazz up these plain white tab-top cafe curtains come right off when it's time to wash them. That's because the buttons are attached with magnets rather than sewn on. Tie hemp cord through each button, then glue a magnet onto the back. Cut burlap into a strip 1-1/2 inches wide, and pull off a few of the long threads to fringe the edge. Lay the burlap on top of the curtain and hold it in place with a magnetic button at each tab.
Easy Roman Shade
Create the look of a Roman shade with fabric and tension rods. Watch and see how easy it is.
Made from shawls found for $8 each, these panels are an inexpensive alternative to custom window treatments. Cut away the fringe from one end of each shawl, and hot-glue decorative trim along the raw end. Hang from clip rings.
Floor-Length Tab-Top Panels
Velvet ribbon in three sherbet shades turns plain white tab-top curtains into an elegant treatment. To create the look, lay out the panels and attach horizontal bands of ribbon with fabric glue. To make the ties at the top, cut the tabs off, then cut six evenly placed, 1-inch horizontal slits across each panel. Finish by cutting V shapes out of the ends of each tie.
Tip: Washable fabric glue will be strong enough to withstand a washing machine and will remain clear and flexible.
Printed Roman Shade
Embellish a ready-made fabric Roman shade with a DIY stencil. Print letters one per page in your favorite font. For the silverware, check the Internet or clip art books for an image and enlarge it on a photocopier. Put the patterns under the shade and trace in pencil, then outline with black fabric marker and shade as needed. Hang shade and tack the trim to the window.
For a perfectly centered and spaced word, start with the center letter, then add the next one to the right, then to the left, and so on.
Tip: Many ready-made window treatments can be washed, either by hand or in the machine on the gentle cycle, and machine-dried. If you are in doubt about the care, opt for hand washing.
Add drama to a room by hanging tab-top panels embellished with a grid of ribbon and rickrack. Choosing natural colors and textures keeps the boldness of the pattern in check. Measure carefully and plan ahead for proper ribbon placement. Each X design extends from side to side and repeats three times from top to bottom. Glue down all the caramel-color ribbon first, then center and glue on lengths of lime green rickrack. Finish by gluing a large button at each intersection. For a nicely finished edge, cut the ribbon 1 inch longer than needed, wrap it around the edge of the curtain, and glue it on the back. Finish the look with a button of your choice. We chose a wooden button to complement the caramel-color ribbon.
Tip: Before adding embellishments, first press the draperies to remove all wrinkles and creases. Accurate positioning of ribbons and trims will be easier on a smooth surface.
Confining the embellishment to the edges of this Roman shade keeps the look clean. As the shade is raised, the ribboned edges fall into graceful pleats. We combined several different widths and colors of ribbon. After planning the design, stretch the shade out on a flat surface and glue the ribbons around the outside edges one layer at a time. Allow the ribbons to extend an inch beyond the shade width so they can be folded over and glued to the back for a finished look.
Stenciled Curtain Panels
Dress up purchased panels with a fun stencil. Lay a panel out flat, with kraft paper underneath it to absorb extra paint. Place the stencil on the panel and use fabric paint to paint on the design.
See more no-sew ideas.