Exterior House Paint

Refine By
Valspar
$13.74 $11.15

Exterior house paint and primer in one. Semi-gloss. Great coverage, durability and scrubability. Fade resistance. Surfaces: New wo...od, previously painted surfaces, hardboard siding, masonry, concrete, stucco, block, aluminum, vinyl siding. No.... read more

Prestige Paints
$60.77

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

YENKIN MAJESTIC PAINT
$17.34

Brought to you by yenkin majestic paints, this interior/exterior oil-based floor paint is ideal for use on concrete, wood, and pro...perly primed metal. The powerful formula is scuff, mar, and water-resistant and dries within 8 hours. read more

Majic
$16.87

This item is a Yenkin-majestic Paint 8-1508-2 Interior/exterior Latex Paint Gloss Light Yellow. Purpose of use for Painting Suppli...es, house-paint. This product is manufactured in United States. read more

Prestige Paints
$44.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint that is intended to be used on exterior su...rfaces including properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: *When painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) Actual paint colors may vary from on-screen and printer representation. Surface Preparation: Remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. Prime all bare, new wood and factory primed wood with an oil base primer. Prime masonry surfaces including cementious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 C). Average coverage 400 sq. ft. (37 square meters) per gallon (3.78 L). For best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry Time: Dries in 1 to 2 hours. Allow to dry overnight before recoating. Low temperature or high humidity may increase dry time. Cleanup: Use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint that is intended to be used on exterior su...rfaces including properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: *When painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) Actual paint colors may vary from on-screen and printer representation. Surface Preparation: Remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. Prime all bare, new wood and factory primed wood with an oil base primer. Prime masonry surfaces including cementious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 C). Average coverage 400 sq. ft. (37 square meters) per gallon (3.78 L). For best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry Time: Dries in 1 to 2 hours. Allow to dry overnight before recoating. Low temperature or high humidity may increase dry time. Cleanup: Use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. read more

Kilz
$32.31

A good exterior paint offers coverage and protection against the elements, while adding beauty to outdoor structures. This is an a...ll purpose exterior paint resists cracking, peeling and blistering. This paint features a unique water/oil base formula for exceptional adhesion, versatility, and longevity in varied conditions. Use on vertical exterior wood surfaces as well as masonry, stucco, and sanded glossy surfaces. Remove mildew, peeling paint, mill glaze, loose wood fibers, dirt and debris before painting. This paint dries to the touch in 2-3 hours. Allow 6 to 8 hours of drying prior to recoating. This is a 1-gallon can of KILZ Exterior Siding, Fence, and Barn Paint in red. For use on properly prepared exterior vertical wood surfaces. Coverage varies by porosity from approximately 200 square feet per gallon on porous surfaces to up to 500 square feet per gallon on smooth, nonporous surfaces. Keep a wet edge and always back-brush or back-roll during all application methods. Paint can be sprayed, brushed, or roll on. KILZ has been making premium primers and paints for 40 years. read more

Rust-Oleum
$46.74 $44.11

Gallon, Perma-White, Mildew Proof Exterior Paint, White Satin Finish, Guaranteed To Prevent Mildew For 5 Years, 100% High-Performa...nce Acrylic Formulation, Long-Term Durability, Outlasts Ordinary House Paint, Self Priming On Most Applications, 2 Coat Application, Moisture, Peel, & Crack Resistant, Can Be Tinted To Off White & Pastel Colors, Check MOL Restricted Items Report To Verify Restrictions For Your Location. read more

Kilz
$24.99 $19.92

This high-quality, acrylic latex water-base interior/exterior paint offers excellent hiding properties with great adhesion and wat...er repellency on textured interior and exterior surfaces. This self-priming paint offers a mildew resistant finish on properly prepared smooth, rough and textured masonry, drywall, stucco, and brick surfaces. It is alkali-resistant up to pH 12.0, easy to apply, and cleans up with soap and water. This formula is designed to accentuate all textured surfaces while achieving a natural look. This is a 1-gallon can of KILZ Interior/Exterior Concrete, Brick, and Tile Paint in tan with a flat finish. Covers 250-400 square feet per gallon depending on surface texture. All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew stains, loose and peeling paint, rust, and all other foreign substances. This paint can be rolled, brushed, or sprayed on. KILZ has been making premium primers and paints for 40 years. KILZ was named Paint Brand of the Year in 2015 in the Harris Poll EquiTrend Rankings. read more

True Value
$20.58

True Value Mfg. Company KEFN-GL Neutral Flat Latex Interior And Exterior Paint 1 Gallon is for indoor and outdoor use. Latex based.... Resists fading. Long lasting. High hiding coverage. Resists mildew and fading. read more

Kilz
$24.99

This high-quality, acrylic latex water-base interior/exterior paint offers excellent hiding properties with great adhesion and wat...er repellency on textured interior and exterior surfaces. This self-priming paint offers a mildew resistant finish on properly prepared smooth, rough and textured masonry, drywall, stucco, and brick surfaces. It is alkali-resistant up to pH 12.0, easy to apply, and cleans up with soap and water. This formula is designed to accentuate all textured surfaces while achieving a natural look. This is a 1-gallon can of KILZ Interior/Exterior Concrete, Brick, and Tile Paint in gray with a flat finish. Covers 250-400 square feet per gallon depending on surface texture. All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew stains, loose and peeling paint, rust, and all other foreign substances. This paint can be rolled, brushed, or sprayed on. KILZ has been making premium primers and paints for 40 years. KILZ was named Paint Brand of the Year in 2015 in the Harris Poll EquiTrend Rankings. read more

DUTCH BOY
$22.72

When you have children, pets, or messy adults, the dirt can wreak havoc on the wall paint. What you need is the DUTCH BOY dirt fig...hter latex paint. This exterior satin paint is formulated to resist peeling, blistering and cracking while providing a mildew-resistant coating, making your home look as if its never seen the light of day read more

Valspar
$26.43 $25.99

Valspar Oil and Latex Barn & Fence paint flows on smoothly and dries to a tough, durable finish. It is fade and weather resistant.... read more

True Value
$207.36 $207.35

Sgwp, weather all, 5 gallon, pastel base, exterior 100% acrylic latex semi-gloss house & trim paint, premium quality, all weather ...durable, high hiding for excellent coverage, mildew resistant, stain & fade resistant for a fresh look longer, easy soap & water clean up, lifetime warranty, VOC less than 50 grams per Litre. read more

True Value
$29.29 $26.44

True Value Mfg. Company HPX9-QT Premium Weather All White Exterior Flat Acrylic Latex House Paint 1 Quart is fade resistant. Latex... based exterior house paint provides excellent coverage. read more

Valspar
$23.57 $17.96

This item is Valspar Brand 1 Quart Flat White Climate Zone Exterior Latex House Paint 44-2730 . Used For Painting Supplies, Paint ...& Stains Accessories. The product is manufactured in United States. read more

True Value
$147.77 $138.80

JES-9, Painter's Select Everyday, 5 Gallon, White, Exterior Satin 100% Acrylic Latex House Paint, Durable Acrylic Satin Finish, Hi...gh Hiding Coverage, Resistant To Mildew & Fading, Easy Soap & Water Clean Up, 15 Year Warranty, VOC Less Than 50 Grams Per Litre. read more

Valspar
$33.92 $17.99

This item is Guardian 44-755g Contractor Grade Exterior Latex Semi-gloss House & Trim Paint, 1-gallon, White . Used For Painting S...upplies, Paint & Stains Accessories. The product is manufactured in United States. read more

True Value
$15.08

True Value Mfg. Company HPXT-GL Premium Weather All Tint Base Exterior Flat Acrylic Latex House Paint 1 Gallon is fade resistant. ...Latex based exterior house paint provides excellent coverage. read more

True Value
$131.90

True Value Mfg. Company JEFT-5G Painter's Select Everyday Tint Base Exterior Flat Latex House Paint 5 Gallon features a durable ac...rylic flat finish. High hiding coverage. Resistant to mildew and fading. Easy soap and water cleanup. Fifteen year warranty. read more

True Value
$45.70 $44.34

JES-9, Painter's Select Everyday, Gallon, White, Exterior Satin 100% Acrylic Latex House Paint, Durable Acrylic Satin Finish, High... Hiding Coverage, Resistant To Mildew & Fading, Easy Soap & Water Clean Up, 15 Year Warranty, VOC Less Than 50 Grams Per Litre. read more

True Value
$133.71

Jef-9, painter's select everyday, 5 gallon, white, exterior flat latex house paint, durable acrylic flat finish, high hiding cover...age, resistant to mildew & fading, easy soap & water clean up, 15 year warranty, voc less than 50 grams per litre. read more

Prestige Paints
$39.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$40.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$43.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A flat finish provides a smooth, uniform look. Flat or "matte" finishes get their name from the lack of reflection from the painted surface. This is one of the benefits of a matte finish, because it helps hide surface imperfections, such as dents, nail holes, or patches. Flat finishes often require fewer coats than semi-gloss and gloss paints and also are easier to touch up because there is less contrast between the touch-up paint and the rest of the painted surface. *Prestige paints uses proprietary base paints and tints to create and match colors. Works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A flat finish provides a smooth, uniform look. Flat or "matte" finishes get their name from the lack of reflection from the painted surface. This is one of the benefits of a matte finish, because it helps hide surface imperfections, such as dents, nail holes, or patches. Flat finishes often require fewer coats than semi-gloss and gloss paints and also are easier to touch up because there is less contrast between the touch-up paint and the rest of the painted surface. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$41.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$39.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A flat finish provides a smooth, uniform look. Flat or "matte" finishes get their name from the lack of reflection from the painted surface. This is one of the benefits of a matte finish, because it helps hide surface imperfections, such as dents, nail holes, or patches. Flat finishes often require fewer coats than semi-gloss and gloss paints and also are easier to touch up because there is less contrast between the touch-up paint and the rest of the painted surface. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A flat finish provides a smooth, uniform look. Flat or "matte" finishes get their name from the lack of reflection from the painted surface. This is one of the benefits of a matte finish, because it helps hide surface imperfections, such as dents, nail holes, or patches. Flat finishes often require fewer coats than semi-gloss and gloss paints and also are easier to touch up because there is less contrast between the touch-up paint and the rest of the painted surface. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$40.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$39.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$39.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$44.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$40.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$41.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method read more

Prestige Paints
$44.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$58.80 $58.57

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$43.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$40.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$40.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$41.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A flat finish provides a smooth, uniform look. Flat or "matte" finishes get their name from the lack of reflection from the painted surface. This is one of the benefits of a matte finish, because it helps hide surface imperfections, such as dents, nail holes, or patches. Flat finishes often require fewer coats than semi-gloss and gloss paints and also are easier to touch up because there is less contrast between the touch-up paint and the rest of the painted surface. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$43.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A flat finish provides a smooth, uniform look. Flat or "matte" finishes get their name from the lack of reflection from the painted surface. This is one of the benefits of a matte finish, because it helps hide surface imperfections, such as dents, nail holes, or patches. Flat finishes often require fewer coats than semi-gloss and gloss paints and also are easier to touch up because there is less contrast between the touch-up paint and the rest of the painted surface. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$43.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$43.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. A semi-gloss finish is more reflective than satin, but is not as shiny as gloss. Semi-gloss finishes provide walls with a shiny appearance and brighten a wall's appearance. Off-whites and pale shades of lighter colors are punched up and made brighter by the glossy effect created with these finishes. They are ideal for use in areas with high humidity. They are also the easiest to clean (with light scrubbing or wiping), compared to other finishes. The downside to a gloss finish is that it shows almost every imperfection on a wall. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Prestige Paints
$47.99

Prestige Paints 100% acrylic exterior latex paint and primer in one is a high end paint intended to be used on exterior surfaces i...ncluding properly prepared wood, masonry surfaces, cement board siding, vinyl*, aluminum, and factory primed siding. (Note: when painting vinyl siding do not paint with any color darker than the original siding. Painting with darker colors may cause the siding to warp.) surface Preparation: remove dirt, mildew, grease, wax and soap residue, loose and peeling paint. Glossy areas must be dulled by sanding. PRIME all bare, new wood and factory primed wood with an oil base primer. PRIME masonry surfaces including cementitious siding with a latex primer. Application: Stir or mix paint before using and intermix all containers for color uniformity. Apply as is with a high quality brush, roller or pad painter. Thin sparingly with water if necessary for spraying. Do not overspread. Temperature must be above 50 F (10 c). average coverage 400 sq. Ft. (37 square meters) per gallon (3.78 L). for best performance, apply two coats of paint on new surfaces after priming. Do not use indoors. Dry time: Dries in 1 to 2 hours. Allow to dry overnight before coating. Low temperature or high humidity may increase dry time. Cleanup: use warm water and soap. Satin finish paints are probably the most commonly used finish on exterior surfaces. Satin finishes resist mildew effectively and are easier to clean than flat or eggshell finishes, and can be wiped down or scrubbed lightly. On exterior surfaces, satins are ideal for painting siding that is in good to excellent condition. Outside surfaces painted with satin paint also shed water effectively and don't fade quickly from the sun. They are also a good choice for painting trim and shutters. *Prestige paints uses proprietary base paints and tints to create and match colors. Prestige Paints works with industry leaders in paint color to match the color on this page based on the color specifications of the original to create a comparable color. Prestige Paints is not offering the ACTUAL branded color or paint product for sale and is not associated or affiliated with the color-referenced brand. Prestige Paints reference to any trademark is for color comparison only. Actual paint colors may vary from on-screen and printer representation. Note that color can vary due to sheen, light, surface, and application method. read more

Products at Walmart
Better Homes and Gardens Real Estate
Bouquets from FTD

This item has been added to your list

This item has been added to your sale alerts