Forrest Forrest WW08407100 Woodworker II 8-Inch 40 Tooth ATB General Purpose Saw Blade with 5/8-Inch Arbor

With this all purpose blade for tables saws you can rip and crosscut 1" - 2" rockhards and softwoods resulting in a smooth-as-sanded surface. With 20 DEG face hook, ply-veneers will crosscut with no bottom splinter at moderate feed rates. D...ouble hard and 40% stronger C-4 carbide will give up to 300% longer life between sharpenings. Ends blade changing (one blade does rip, combo and crosscut). Ends second-step finishing. Ends cutting 1/16" oversize to allow for resurfacing. Buy and sharpen one blade instead of 3, (24T rip, 50T combination, 80T crosscut). read more

Forrest
$310.00
at Amazon

The Forrest NM1612011180 Circular Saw Blade is an all-purpose blade for table saws that leaves edges ready to use with minimal pla...ning and sanding. The Forest NM1612011180 Blade is double hard for a longer cutting life and made for cutting wood between 1 and 2 inches thick. read more

Forrest
$77.00
at Amazon

With this all purpose blade for tables saws you can rip and crosscut 1" - 2" rockhards and softwoods resulting in a smooth-as-sand...ed surface. With 20 DEG face hook, ply-veneers will crosscut with no bottom splinter at moderate feed rates. Double hard and 40% stronger C-4 carbide will give up to 300% longer life between sharpenings. Ends blade changing (one blade does rip, combo and crosscut). Ends second-step finishing. Ends cutting 1/16" oversize to allow for resurfacing. Buy and sharpen one blade instead of 3, (24T rip, 50T combination, 80T crosscut). read more

Forrest
$127.00
at Amazon

Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut e...dge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. Forrest Woodworker 1 Saw Blade For Radial and Table Saws. These trim and cross-cut ALL PURPOSE blades give scratch-free POLISHED cuts on wood, RIP or CROSSCUT, up to 2' thick. They have a 30° Alternate Top Bevel with a 5° Face Hook on 10' diameters and smaller.Saves 1/3 wood loss on each cut.Feeds easily when used for moderate rips and crosscuts on a table saw.Reduces 'JUMP IN' for better 'PULL-CONTROL.'Eliminates bottom splintering on RADIAL CROSSCUTS.With new 30�� ATB tooth style this blade stops totally, ALL bottom and top splintering on ply veneers on both radial and table saw machines read more

Forrest
$175.00
at Amazon

Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut e...dge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new.No splinters cross-cutting oak, ply veneers and melamineCuts in all directions- rip, cross-cut, miter, any depth.Cuts all sized grooves 1/4' through 29/32' increments. (Set of plastic adjusting shims also included)Super-hard carbide gives up to 300% longer life, especially good on plywoods and abrasive particle-boards.Are hardened and precision ground flat within .001' to keep your blade true. read more

Forrest
$249.00
at Amazon

Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut e...dge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. Recommended for: thin, low pressure, two-sided laminates, plywood & fine cross cutting on all woods. Eliminates need for a small scoring saw blade on table saw work. The 40° points slice through thin bottom layers with no tears or chips. Reduced yearly sharpening costs - less machine downtime.No splinters cross-cutting oak, ply veneers and melamineCuts in all directions- rip, cross-cut, miter, any depth.Cuts all sized grooves 1/4' through 29/32' increments. (Set of plastic adjusting shims also included)Super-hard carbide gives up to 300% longer life, especially good on plywoods and abrasive particle-boards. read more

Forrest
$265.00
at Amazon

The Forrest MM14107 Circular Saw Blade is an all-purpose blade for table saws that leaves edges ready to use with minimal planing ...and sanding. The Forest MM14107 Blade is double hard for a longer cutting life and made for cutting thin, low pressure, two-sided laminates, plywood & fine cross cutting on all woods between 1 and 2 inches thick. read more

Panasonic
$637.00
at Amazon

Panasonic EYC18DV42- 18.V IP56 Li-ion 2pc "Impact Driver" Combo Kit. EYC18DV42 is a member of the Panasonic ToughIP Tool series an...d has passed the IP standard test administered by the International Electro technical Commission (IEC) receiving an IP56 rating, dust and water resistant. Panasonic's dust and water resistant technology has been demonstrated to comply with the IP standard by tests designed to gauge the level of protection against the intrusion of dust and water. The EYC18DV42 combo kit consists of EY74A1 Dual Voltage Drill Driver and EY75A1 Dual Voltage Impact Driver. The drill driver, EY74A1 delivers high power at any speed in a compact length- 8" lightweight - 4.3lbs frame. The drill has an 18-stage clutch plus drill position, 1/2-inch, heavy-duty keyless chuck, variable speed, 2-speed gear box, electric brake and quick-charging system and LED work light . The drill is ideal for general construction, plumbing, electric installation work and finish carpentry. The EY75A1X Impact Driver delivers high torque fastening, stays cool and comfortable. The EY75A1's 1,370 in.lbs power and 3 speeds make short work for tough jobs.. Its lightweight of 3.53lbs, compact style reduce fatigue, while its new brushless motor and electronic switch increase the motors lifespan by about twice as long as our conventional motor. The EYC18DV42 2pc Impact Driver Combo kit is powered by 4.2ah Lithium Nickel battery packs, highest capacity battery pack on the market.. This battery pack delivers high output with low heat generation resulting in longer run time. . In addition the 18V drill/driver and impact driver combo kit utilizes Panasonic's unique Guard ION system. The Guard ION system monitors each battery cell during battery charging and during tool use to prevent over discharging and overheating of the battery pack thus insuring long life. The kit consists of a drill/driver, impact driver, 2 - 4.2Ah Li-ion battery packs, charger and carry bag. read more

Forrest
$310.00
at Amazon

The Forrest NM1612011180 Circular Saw Blade is an all-purpose blade for table saws that leaves edges ready to use with minimal pla...ning and sanding. The Forest NM1612011180 Blade is double hard for a longer cutting life and made for cutting wood between 1 and 2 inches thick. read more

FASCO
$658.00
at Amazon

The Fasco Plier Staplers for Carton Type applications can accept interchange and/or genuine brand name staples. These tools are ve...ry dependable and durable. They fire all of the brand name staples including JK, BEA, Bostitch and Senco along with generic interchange fasteners. read more

Makita
$970.00
at Amazon

Includes 14-in Angle Cutter - 4114-R, Socket Wrench - 782210-8, Operating Manual

Powermatic
$4,250.00
at Amazon

1792016K Features: -Distressed:No -Power Source:Electric -No Load RPM:2000. Dimensions: -Overall Height - Top to Bottom:38 -Overal...l Width - Side to Side:37 -Overall Depth - Front to Back:85 -Overall Product Weight:755 read more

Makita
$458.00
at Amazon

Includes 1-1/8 in. SDS-plus Rotary Hammer w/ LED Light - HR2811F, Side Handle - 154842-5, Depth Gauge - 324219-0, Plastic Carrying... Case - 824789-4 read more

View wishlist Set Sale Alert Continue shopping
View Sale Alerts Continue shopping