Refine By
Beadaholique
$5.49
at Amazon

These delightful silver color steel beads add sparkle and jingle to jewelry and clothing. Cluster several on an anklet, sew onto s...carves, belts or purses. Just a few hanging from earring hooks make a cheery holiday piece. These little bells are hollow with a split along the bottom edge, so they make a pleasant sound, but they don't ring loudly. Beads are approximately 8mm long and 6mm across. Hole at top measures 1mm in diameter. Quantity: 100 Beads. read more

Beadaholique

Epoxy Stickers For Scrabble Tiles, Scrapbooking And Crafts Great Alternative To Resin Useful For Collage Art Projects Quantity: 10...0 Measurements: 18.5x20.4mm. Use these rectangular epoxy stickers to create a 3D look in your project! Great as an alternative to resin and glazes. NOTE: Keep out of direct sunlight for extended periods of time. Prolonged exposure to sunlight may cause the stickers to yellow. Measurements: 18.5x20.4mm, 2.3mm thick. Quantity: 100 Also available in quantities of 25, 50 and 200. -----How to make a Scrabble tile pendant using square epoxy stickers----- Carefully peel the clear square epoxy sticker off of its protective backing, being careful not to touch the sticky side. Place the sticker directly on top of the image you are using. Press firmly with your fingers to remove any air-bubbles and to help secure the adhesive bond. Cut out the image with the sticker on top - carefully cutting along the edge of the sticker, making sure not to cut the sticker itself. Spread glue (a white glue such as Nunn permanent glue or Crafter's Pick works fine) on the backside of the cut out image/sticker. Center the image/sticker glue side down onto the non-letter side of the Scrabble tile (check the orientation of the letter on the back to make sure it's facing the right direction). Press into place and let dry. You can easily add a glue on bail such as an Aanraku bail to the back of the pendant once the front side is dry. It is recommended to use E6000 industrial read more

Beadaholique
$9.95
at Amazon

Blank Crown Bottle caps Shiny Silver Color NO Liners For Pendants, Crafts, Scrapbooking, Etc. 1 Inch Interior Diameter 50 Bottle C...aps blank slate for your crafting projects! Standard size crown bottle caps with a shiny finish. Inside is standard silver grey. Make pendants, earrings, magnets, bracelets, use in scrap-booking, use grommets to attach to belts, the options are endless! These are new and un-used with no liner. Use 2-part epoxy or a resin product such as Lisa Pavelka Magic-Glos UV Resin to embed a photo, design, even a small charm or other object into a clear, dimensional glossy finish. Glue on pendant bails using E-6000 adhesive for an easy way to hang these from a chain without having to drill or punch a hole. 32mm in diameter (1 1/4 Inch). Interior diameter 26mm (1 Inch). Height is 5.5mm (.22 Inch) Quantity: 50 Bottle Caps. read more

Beadaholique
$5.75
at Amazon

Wire Protectors hide and protect thread and beading wire up to .021 Inch diameter from the everyday wear and tear caused by toggle...s, clasps or other findings. Use like French wire to put the finishing touch on your necklaces and bracelets. Also helps you to leave uniform size loops at the end of your pieces. Measurements: 4.5mm total length, 1mm thick Quantity: You will receive 20 loops, enough for 10 complete necklaces. HOW TO USE WIRE PROTECTORS 1) Thread a crimp bead onto your beading wire, followed by a Wire Protector. You'll need to guide the wire through on end hole, around the back (making sure it lays in the channel), and then back out through the other end-hole of the Wire Protector. 2) Next, hook the threaded Wire Protector onto a finding as you would with an open jump ring. 3) Slightly pinch the Wire Protector so that the two end-holes touch, then pull the end of the wire and insert it back through the crimp bead. Now you can crimp the bead, snip the excess wire and begin beading. read more

Beadaholique
$7.30
at Amazon

Wire Protectors hide and protect thread and beading wire up to .031 Inch (.78mm) diameter from the everyday wear and tear caused b...y toggles, clasps or other findings. Use like French wire to put the finishing touch on your necklaces and bracelets. Also helps you to leave uniform size loops at the end of your pieces. Measurements: 4.7mm total length, 1.3mm thick Quantity: You will receive 10 loops, enough for 5 complete necklaces. HOW TO USE WIRE PROTECTORS 1) Thread a crimp bead onto your beading wire, followed by a Wire Protector. You'll need to guide the wire through on end hole, around the back (making sure it lays in the channel), and then back out through the other end-hole of the Wire Protector. 2) Next, hook the threaded Wire Protector onto a finding as you would with an open jump ring. 3) Slightly pinch the Wire Protector so that the two end-holes touch, then pull the end of the wire and insert it back through the crimp bead. Now you can crimp the bead, snip the excess wire and begin beading. read more

View wishlist Set Sale Alert Continue shopping
View Sale Alerts Continue shopping