- view all thumbnails
Installing a drop-in sink and a top-mount, single-handle faucet is a fast and easy kitchen facelift. One thing to consider when choosing a new sink and faucet is how many holes the faucet requires. Is it a single-handle unit or does it have separate handles for hot and cold water? Do you need holes for a separate sprayer or soap dispenser? Most drop-in sinks are available with various numbers of faucet holes.
Tip: If you end up with different setups, such as a one-hole faucet and a three-hole sink, you can make it work by using the plate, called an escutcheon, that typically comes with the faucet to cover unused holes in the sink.
Measure the width of the base cabinet in which your sink will be installed. A sink should be four inches narrower than the cabinet to allow room for a mounting that doesn't require modifications of the cabinetry.
To complete this project you will need the following tools and materials: a sink, a faucet, a strainer set, a basin wrench, water pump pliers, a crescent wrench, a screwdriver, a putty knife, plumber's putty, silicon sealant, a flashlight, a bucket, and towels. Keep a jigsaw close by in case you need to enlarge the opening in the countertop.
The copper lines that supply hot and cold water to the sink often have shutoff valves under the sink. Turn them off. In some homes, you may need to turn off water elsewhere, such as at the lines in the basement that lead to the sink. Once the water supply is off, turn the faucet on to let water and pressure drain from the lines. If you have a garbage disposal, turn off the breaker panel switch that provides electricity to the kitchen and unplug the disposal's power cord.
Use a crescent wrench (or a basin wrench if the nuts are difficult to reach) to disconnect the faucet from the supply lines. Then disconnect the sink from the drainpipes using water pump pliers. Keep a bucket and towel handy to clean up the water that inevitably will spill from the pipes as you disconnect them.
Disconnect the disposal from the sink by loosening the ring that attaches the disposal to the sink flange. The best way to do this is to insert a long screwdriver into the lugs on the ring and twist. When the disposal is loose, lift it off the drainpipe. You also must remove the disposal's mounting bracket from the bottom of the sink drain; you'll need it to attach the disposal to the new sink. To remove the mounting bracket, pry the retaining clip off the drain flange, then loosen the screws on the bracket.
Your new sink's box should include a template that shows you how large the countertop opening must be. Use it to check the existing opening. If your new sink is the same size as your old one, you should be able to drop it into the existing opening. If your new sink is larger than the old one, enlarge the opening in a laminate countertop by cutting it with a jigsaw. If you have a slab countertop, such as stone or quartz-surfacing, you will not be able to change the size of the opening.
It's easiest to install a faucet on a new sink before the sink is put in place. Follow the installation instructions for your specific faucet. The process typically involves laying a gasket on the sink, then setting the faucet on top of the gasket with its tailpieces extending through the sink's holes. Tightening a nut on the underside of the sink secures the faucet to the sink.
Confirm the sink's fit by setting it into the new hole, grasping the sink through the drain holes. Lift the sink out and apply silicon sealant around the edge of the opening, being sure not to leave any gaps. Then set the sink in place. Press on the sink to set it in the sealant. If your sink requires clamps to secure it to the countertop, attach those now. Use a damp cloth to wipe any excess sealant off the countertop. Let the sealant cure for 30 minutes before proceeding.
You could use the old strainers in a new sink's drain holes, but getting shiny new ones is usually part of getting a new sink. You often need to purchase these separately from the sink. Apply plumber's putty to the underside of each strainer flange and set the strainers into the holes.
On the sink's underside, attach the gaskets that came with the strainers to the strainer flanges. Then attach the drainpipes to the strainers and tighten the nuts. (You may need to adjust the lengths of the drainpipes if your new sink's shape is different from the old one's.) If you have a garbage disposal, reconnect it to the sink flange, insert its drainpipe, and plug the power cord in. Reconnect the faucet by reversing the steps you took to disconnect the water lines. Turn on the power to the kitchen.
Try our FREE ultimate decorating toolbox to design your kitchen. Imagine it, plan it, then do it with Decorating Inspiration!