Build a Bird-Pattern Fence

Here's a fence design for bird lovers.


+ enlarge image Feathered friends will flock together on this fence.

Preassemble as many components as you can in your basement, garage, or workshop. Then move outside, set the posts, and fasten everything together.

What You Need:

  • Scrap of 1/4-inch plywood (for quail template)
  • Water-resistant adhesive
  • Zinc-plated screws
  • Galvanized nails
  • Jigsaw or scroll saw
  • Circular, table, or radial-arm saw
  • Router
  • Drill
  • 60- and 100-grit sandpaper
  • Framing square
  • Level
  • Hammer
  • Screwdriver
  • Posthole digger
  • Premixed concrete (optional)
  • Stain or clear finish (see the page "Choosing a Finish" for advice)
  • Clean rags or paintbrush

Additional Materials

For each fence section 6 feet 7-1/2 inches long, including posts (the capital letters correspond to the Diagram page):

+ enlarge image Imagine having your very own flock of quails.
  • Two 6x6x56-inch cedar, redwood, or pressure-treated posts (A), rated for ground contact (Add the depth of the frost line in your region to the length if you'll be setting the posts in concrete.)
  • One 15-inch length of 2x8 rot-resistant lumber (for post caps, B)
  • 2 decorative finials (C)
  • One 8-foot length of 2x4 rot-resistant lumber (for end boards, D)
  • Two 8-foot lengths of 2x3-inch rot-resistant lumber (for rails, E)
  • Three 8-foot lengths of 1x4 rot-resistant lumber (for spacers, F)
  • Four 10-foot lengths of 1x8 rot-resistant lumber (for pickets, G)
+ enlarge image Use this grid as a guide for sizing the "birds."

1. Print out the diagram on the next page.

2. Make the posts. With a router, chamfer each post corner as shown in illustration. For the cap, rout 7-1/2-inch square by 1-1/2-inch stock (B) with a cove bit. Round-over the cap edges and corners. Attach a cap to each post with water-resistant adhesive and galvanized nails. Finally, drill a pilot hole in the center of each cap and screw in a finial.

3. Construct the frame. Round-over the ends and edges of two 2x4 end boards (D). Cut two 2x3 rails (E) 65-1/2 inches long. Attach the end boards to the rails by drilling pilot holes and driving zinc-plated screws through the end boards into the ends of the rails. Make sure the rails are square with the end boards.

4. Construct the fencing. For the five spacers (F), cut 1x4s to length and round the top edges. Cut eight 60-inch-long pickets (G). Enlarge the pattern and transfer it to a piece of 1/4-inch plywood. Cut out the plywood quail, then use it as a template for shaping the tops of the pickets. Use a scroll saw or jigsaw to cut quails in the picket tops. Nail the pickets and spacers to the rails, spacing them 1 inch apart.

5. Assemble the fence in place. Set and plumb the posts, referring to the page "How to Set a Post" for more advice. Install the preassembled fencing unit by driving screws through the end boards (D) into the posts.

6. Apply a finish, using paintbrush or rags. (See the page Choosing a Finish.)

+ enlarge image Print this diagram and keep it handy while you construct the fence.

Wood has two formidable outdoor foes: moisture and sunlight's ultraviolet (UV) rays. Different exterior finishes provide differing degrees of protection against wood's natural enemies. Here are your choices:

Clear finishes include varnishes, water repellents, and penetrating oils. These finishes shield wood from water while allowing its color to show through, but they also let UV rays penetrate the grain, causing the wood to break down. Adding a UV-filtering agent to a finish retards this reaction, but doesn't prevent it entirely.

Semi-transparent stains let a wood's natural grain and texture show through but will alter the wood's color. They are usually oil-based and offer minimal protection against UV rays, so you'll have to recoat every few years.

Semi-solid stains have more pigment than semi-transparent stains and are more UV-resistant as well.

Opaque stains resemble paint in the sense that they conceal a wood's natural color, but they allow the texture to show through. They do a good job of resisting UV rays and are available in either an oil or a latex base.

If you're up to mending your fence every few years, you can simply dig holes in the ground, drop in posts, and pack earth around them. For a more lasting installation, you'll need to protect the posts against rot by setting them in or on a concrete footing.

If you decide to set posts in concrete, pour a footing that is several inches larger than the post and below the frost line for your region. Unless you're setting a lot of posts, use bags of premixed concrete. While the concrete is still wet, set and plumb each post. When you set a post in concrete, taper the concrete around the post 2 inches above ground level to help shed water that can collect around the base and cause rot.

Home centers sell a variety of post anchors. You can also buy adjustable post bases that fit over machine or carriage bolts set in the concrete footing. These types of anchors allow you to make minor lateral adjustments when you plumb the posts.

Your Comment:
close
close
close
close
close

Loading... Please wait...