Inside the Innovation House

We pulled out all the stops to bring the latest home tech features to our Innovation Home. See the 16 coolest things from the home and be amazed by how smart one home can be.

View Video

Bathroom Countertop Ideas

Good-looking countertops -- whether made of marble, limestone, or concrete -- create high-functioning bathrooms that spill over with style. These popular countertop materials are sure to inspire a bathroom remodel.

View Slideshow

Find Your Dream Backyard

Whether you dream of sunning by a state-of-the-art pool or strolling through a simple cottage garden, there's an outdoor oasis with your name written all over it. Take this quiz to find out where you really belong.

See More

DIY Patio Ideas

Want to boost the beauty and usefulness of your outdoor spaces? Put one of these inspiring DIY patio ideas to work in your landscape.

View Slideshow

Easy Fireplace Upgrades

Does your fireplace need a facelift? Check out these 20 ideas for updating your fireplace with easy-to-apply embellishments and simple-to-make constructions.

View Slideshow

8 Cutting-Edge Exterior Features

The wow-factor of the Innovation Home starts with great curb appeal. See the eight things that make the home's exterior stand out.

View Video

Budget Curb Appeal

Be the best home on the block for less. These budget curb appeal updates will show you how.

View Video
Popular in Home Improvement

Tree Bench

Encircle a tree with a wooden hexagonal bench.

To build your own shady retreat, first choose a tree where you would like to sit in a quiet, secluded area, maybe overlooking a favorite part of the yard. The tree should not be tilted too much and should not have many visible roots. The method of construction is to first build the bench in two sections, then to locate the post holes by holding the bench temporarily in place.

Before You Start:

Purchase or rent a power miter box or radial saw -- something that can make precise 30-degree cuts. Measure your tree's diameter18 inches from the ground to determine the inside dimension of the bench. Use pressure-treated lumber for the posts and supports, and cedar, redwood, orpressure-treated lumber for the seat pieces. Draft at least one helper for the final assembly.

What You Need:

  • 4x4 posts
  • 2x4s for seats and supports
  • 3-inch galvanized deck screws
  • 5-inch hex bolts, nuts, and washers
  • Gravel


Step 1.

1. Assmeble supports. Put together six bench supports, using 2x4 pieces and screws. The faces of these will show, so make sure the ends of the three pieces are evenly cut and flush.

Step 2.

2. Cut the inside pieces. Cut six pieces of 2x4 to be used as the seat pieces closest to the tree. The measurement of the longest side will equal the diameter of your tree. (If you have a fast-growing tree, make them 2 inches longer.) With two helpers, hold up all six pieces around the tree to make sure they are the right size.

Step 3.

3. Start the layout. On a large, flat surface, lay out the first bench section (half the circle), using four seat support sand three of the bench pieces that you have just cut. Adjust them so that all angles are equal. Do not assemble yet.

Step 4.

4. Cut and install boards. Trim the rest of the boards, using the already-cut boards as guides. After positioning them tightly, install them with 3-inch galvanized deck screws.

Step 5.

5. Build the second section. This will only have two bench supports, so screw pieces of 2x4 onto the bottom of each end for temporary support.

Step 6.

6. Set the sections. Set the two sections in place by resting them on chairs. When the whole assembly is positioned correctly, hang a plumb line from the center of each bench support and dig up a bit of turf to mark each posthole. Shift the whole assembly to avoid large, exposed roots.

Step 7.

7. Dig the postholes. You will probably run into underground roots. Do not cut large roots, or you may kill the tree. As a general rule, any root less than 1 inch in diameter can be cut. Some post holes -- nomore than three -- can be left shallow. Shorten the posts accordingly. Be sure the holes are wide enough.

Step 8.

8. Install the posts. Cut six4x4 posts to the correct length -- the depth of the hole plus 16 inches. Cut a ten on one end so that the post will fit into the bench support. With your bench sections upside down, install each post, fastening it securely with a 5-inch hex bolt, a washer, and a nut.

Step 9.

9. Set the bench. Set the section with four bench supports in the post holes first. Then lower the other section into place. Make adjustments until the bench is level all around. Install the final screws, set the posts into the holes, and tamp in place.


Loading... Please wait...