Upgrade a Basic Bookcase

Put a personal spin on an off-the-shelf bookcase with these easy DIY makeover ideas.

View Video

Stairway Railing Ideas

Stairway railings serve more than a functional purpose -- they give stairs a visual presence and make a staircase a work of art. Find ideas for the perfect railing for your stairway.

View Slideshow

Beach Chic Porch Renovation

A family put a new roof over their heads by turning their back deck into a coastal-inspired covered porch. Learn how they made the big change from their existing porch to their new, cozy family hangout area.

View Slideshow

Give a Plain Mirror a Makeover

Take a plain mirror to the next level with these easy DIY embellishments.

View Video

DIY Outdoor and Garden Projects

Sprucing up your outdoor space doesn't need to be a massive undertaking. Use these inspirational small projects -- including painting rocks to hanging new house numbers -- to instantly improve the look of a garden, patio, deck, or backyard.

View Slideshow

Add Storage Around Stairs

Step up your home's storage capacity by making the most of underused areas below and beside your stairs. Here's a look at 18 homes that beautifully optimized stairwell and staircase spaces.

View Slideshow
Popular in Home Improvement

Installing Wainscoting

This step-by-step guide teaches how to install wainscoting and includes a list of required materials and tools.

Beaded-board wainscoting updates a room without breaking your budget.

Sometimes all a room needs to make it sparkle is a little attention to detail. Wainscoting adds character and architectural detail in just a few hours.

The typical height for wainscoting is 32 to 36 inches up from the floor or about one-third of the height of the wall. A good way to cap the panel is with a chair rail. For a more dramatic look, run the wainscoting two-thirds of the way up the wall and top it with a picture rail.

Materials:

  • Beaded-board panels
  • Base molding
  • Cap molding
  • Electrical outlet box extenders
  • Construction adhesive
  • Finishing nails and brads
  • Paintable caulk and putty
  • Paint

Tools:

  • Tape measure
  • Carpenter's level or water level
  • Chalk line
  • Safety goggles
  • Handsaw or circular saw
  • Jigsaw or keyhole saw
  • Hammer and nail set or air-driven nail gun
  • Miter box
  • Caulk gun
  • Paintbrush or roller

Preparation:

Several days before painting or installation, acclimatize the panels to your house. Stack them horizontally, placing thin blocks of wood between the panels so air can circulate. This allows any excess moisture to escape and helps reduce expansion or contraction. Remove any base moldings in the room where you will be applying the panels; you'll add new ones to complete the project. If your panels are unfinished, you may want to paint or stain them before installation.

Note: Use safety equipment for the cutting, sanding, and painting necessary to complete the project.

Beaded-board wainscoting is named for the rounded beadlike strips that hide the edges between tongue-and-groove planks. It is especially useful in high-traffic area to protect walls against dings and dents while adding both texture and visual height.

1. Measure and Mark
Because most floors are not level, you'll want to create a level line on the wall to mark the top of your wainscoting panel installation. Base molding installed later will disguise any variance at the bottom edges. Choose a starting point on your wall, and measure the desired height of the wainscoting. (Remember that the cap molding applied along the top edge of the beaded-board panels will add slightly to the finished height.) From that point, use a level to draw a horizontal line and extend it around the room. Use a chalk line to connect the points.

2. Cut
Using a handsaw or circular saw, cut the wainscoting panels to the desired height. Measure the positions of any outlets or other electrical boxes on the wall, then sketch the dimensions onto the backs of the corresponding panels with a pencil. Use a jigsaw or keyhole saw to cut the holes. Install a box extender at each electrical point to contain wires.

3. Fasten
Squeeze construction adhesive in a zigzag pattern onto the wall side of a panel and press the wainscoting panel into place. Nail along the edges as indicated by the manufacturer. If you're hammering the nails by hand, use a nail set to indent each nail so you can cover it with putty. Repeat with the remaining panels. As you apply each panel, make sure you space and overlap them according to manufacturer recommendations. This allows the panels to expand and contract in response to seasonal humidity and temperature changes.

4. Install Molding
Use a miter box to cut angled joints on the cap molding where walls meet. Fasten the cap molding with brads at the tops of the panels. Install base molding with brads.

5. Finish
Fill visible nail holes with putty, and caulk gaps as necessary. Touch up with paint.

close
close
close
close
close

Loading... Please wait...