Popular in Maintenance & Repairs

How to Change a Doorknob

Replacing a doorknob is an easy do-it-yourself project. To replace a doorknob in your home, follow these steps.


    Everything in this slideshow

    • Get Started

      New doorknobs will give an updated look to your home's doors. Before you shop for a new knob, grab a screwdriver and remove the knob you want to replace (learn how in the following slides). Removing the knob before you shop will give you a sense of what type of replacement knob you'll need. You might even want to take the old knob to the store with you for comparison.

    • Grab a Screwdriver

      To remove a doorknob, the only tool you will need is a Phillips screwdriver (the one with four ridges that come to a point like a pyramid). Start by removing the two screws that hold one side of the old knob into place. For some knobs you will need to remove screws from the other side, too.

    • Pull Knobs Apart

      Both knobs should come off along with the plate that covers the hole in the door. A square steel peg that connects the two knobs and slides into a square hole in the latch will most often come out with the knobs.

    • Pull Out the Latch

      If the latch stays in, simply slide it out. Some latches will slide out the edge of the door with just a little bit of persuasion. With most you will have to remove the two screws that attach to the edge of the door.

    • Take Off the Strike Plate

      Remove the two screws that hold the strike plate to the door frame.

    • Bring Out the Tape Measure

      Measure the distance from the center of the big hole in the surface of the door to the edge of the door. This distance, known as backset, typically equals 2-3/8 inches or 2-3/4 inches. Many replacement doorknobs will work with either backset, but be sure your new knob is designed to work with your measurement.

      Tip: If you are purchasing a knob with a lock, you will want to know which side of the door the locking mechanism is on before you buy a new knob. Doorknobs are not reversible. If you want the lock on the inside of a room, you need to note if it is to the left or right when the latch is facing you.

    • Installation Step One

      Start the installation by determining the style of latch plate you need. Depending on the mortise (the cut-out impression the latch sits in) on your door, you might have to swap out the latch's standard rectangular plate for a round one included in the package. If needed, pry off the standard one with a straight-bladed screwdriver (see left and middle photos) Then, place the new round plate on the latch (right).

    • Insert the New Latch

      Slide the latch into the edge of the door. If it has a rectangular plate, you’ll need to attach it with the two provided screws.

    • Time for the New Knob

      One half of your new doorknob will have the square steel peg. Insert that half into the door first, placing the square peg through the latch mechanism.

    • 10 of 14

      Line Up and Push

      Align the other half of the doorknob with the square pin and the screw holes.

    • 11 of 14

      Attach the Knob

      Attach the new knob with the two screws included with the knob set. If the new doorknob does not cover the screw holes, mortises, or any impressions left by the old hardware, it’s time to break out the wood putty. First, sand down any surface imperfections and fill screw holes and excess mortise areas with a hardening-type wood putty. You can try touching up the affected areas with stain, clear finish, or paint—whatever the door and frame requires—but if that doesn’t blend colorwise, you’ll need to refinish or repaint the entire door or frame.

    • 12 of 14

      Attach the New Plate

      Attach the new strike plate to the door frame with the two screws provided. If you need to enlarge the mortise for the latch plate or the strike plate, make sure you have a sharp chisel and fresh blade for your box cutter. To enlarge the mortise, first define its outer edges with a box cutter. Then position the chisel to remove the excess material.

    • 13 of 14

      Finished Product

      You now have a new doorknob. And now that you know how quick and easy a doorknob change can be, updating all the ugly and/or broken knobs in your home will be a cinch.

    • 14 of 14
      Next Slideshow 15 Ways to Stay Cool & Save

      15 Ways to Stay Cool & Save

      With summers trending hotter and budgets getting tighter, it's tough to stay cool. Here's how to reduce your summer energy bills without breaking the bank.
      Begin Slideshow »



    Loading... Please wait...

    I Did It!
    Share on Facebook
    Uh oh! Please pick a jpg at least 600x600px. Done close
    Choose Cancel close
    Share on Facebook
    Uh oh! Your photo failed to upload. Please try again or visit your profile.
    Done Cancel close
    No one has shared their photo yet.