A vent fan works hard to remove moisture, odor, and mold spores. Eventually, it just plain wears out. The signs? Your mirror is foggy. Mold creeps into your shower stall. The fan roars like a coffee grinder. It's definitely time for a change. New fans are quieter and more effective than ever -- and they are relatively easy to install. To choose a fan with the right cubic feet per minute (cfm) capacity for your bathroom, measure the floor area and multiply by 1.1 for an 8-foot ceiling, 1.25 for a 9-foot ceiling, or 1.5 for a cathedral ceiling. For example, an 8×10-foot bath with an 8-foot ceiling needs a fan rated for 88 cfm or more (80×1.1=88). Buy as quiet a fan as you can afford: The lower the sone number, a measurement of sound volume, the better. A refrigerator produces about 1 sone; ambient office noise is about 3. New fans tend to be larger than old units, which means you'll have to cut a larger hole for your replacement fan. You might also need to add an adaptor to make the transition from the 4-inch vent pipe outlet of the new unit to the 3-inch pipe from your old fan.
Before you start, prep by clearing out the bathroom and laying a drop cloth. Set up a stepladder or stool so you can easily reach the fan.
Tools You'll Need
- Safety glasses
- Work gloves
- Circuit tester
- Drywall saw
- Pry bar
- Strain relief connectors
- Wire stripper
- New fan unit
- Wire nuts
- Electrical tape
- Duct tape
- Vent pipe adapter
- 1-inch general purpose screws
- Drill/driver and bits
- Fan grille
- Turn off power; remove grille
Switch off the circuit breaker serving the vent fan. Flip the wall switch to On to confirm that the power is off. Remove the grille and pull out the plug that supplies power for the motor. Insert a circuit tester into the plug receptacle to reconfirm that the power is off.
- Remove old fan/motor unit
Loosen the fasteners that hold the fan/motor unit to the housing. Some prying with a screwdriver might be necessary to remove the unit.
- Enlarge opening
If you need to enlarge the opening, hold the housing of the new unit on the ceiling to mark cut lines. Use a drywall saw to cut the opening, being careful not to damage any hidden wires or pipes.
- Detach the housing
Unfasten the screws holding the housing to the ceiling joists or, if held by nails, use a pry bar to release it.
- Add a strain relief connector
Attach a strain relief connector (it might not come with the fan) to the cap of the housing junction box. Fish the wires through the connector and tighten screws.
- Connect the wires
Connect the wires to the new fan unit, beginning with the ground (a green-insulated or copper wire). Join white to white and black to black. Hold the wires side by side and twist on a wire nut. Wrap the wire nut with electrical tape, overlapping the bottom of the nut and the wires. Push the wires into the junction box and attach the cover.
- Install the fan housing
Slide the unit into the ceiling cavity. Snap on the vent pipe adapter.
- Install the new fan/motor
Attach the housing and fasten it to a joist using 1-inch general purpose screws. You might need to drill holes in the housing for the screws. Close and fasten the cover of the wiring junction box. Insert the fan/motor into the housing and tighten the fasteners. Plug unit into receptacle on the housing junction box. Switch on the power at the breaker box and test the fan. Attach the new fan grille.
Tips for Replacing a Vent Fan
- Work from an attic if you can. Lay a piece of plywood across the joists as a work platform.
- Make an S-shape hook from a wire coat hanger to hold the fan housing as you work.
- For safety's sake, wear protective goggles to defend your eyes from dust and debris, and gloves to avoid the sharp metal parts of a fan unit.
Most old fans have a 3-inch vent pipe, and new fans have a 4-inch vent pipe. Using duct tape on both ends, attach the vent pipe adapter to the new vent pipe of the fan.
More for You